Cement & Concrete Testing Equipment

Product Details:

The autoclave is suitable for conducting accelerated soundness tests on cements or the autoclave expansion test requiring constant steam pressure with the correspondent constant pressure. It consists of a stainless steel cylinder with a welded heat insulated metal housing attractively finished. The attached control unit encloses a sensitive pressure regulator and pressure gauge. Power switches and pilot lights for controlling the electric heating units. Inside chamber dimensions 10.5 cm diameter x 40.5cm height suitable for operation on 230 V, 50 Hz Single Phase A. C. supply. Supplied complete with test bar holder, special rack to hold specimens above water level in the autoclave and in a vertical position to expose them in the same manner. A Digital PID Controller is fitted for controlling the desired temperature.

Request
Callback

Additional Information:

• Item Code: RLE-95

Product Details:

Specification

 

Request
Callback

Additional Information:

• Item Code: RLE-199

The apparatus is used for determining the fineness of cement in terms of specific surface expressed as total surface area in square centimeters per gram of cement. This is a variable flow type are permeability.

Specification:
The apparatus consists one each of permeability cell 12.5mm I.D. manometer 'U' type mounted on stand with a built in stop cock, perforated disc, plunger rubber stopper, rubber tube 30cm long. Packet of 12 filter paper disc and a bottle of 100ml dibutylphthalate liquid.

Spares & Accessories:
Punch to cut filter paper discs. Non-perforated disc. Suction bulb 

Request
Callback

Flow Table ( Hand operated )

RLE-521

AS PER IS CODE - 6932 ( PART VIII) ASTM C 230,BS 4551:1

Specification:
The flow table consists of a 30 cm dia polish steel plate with 3 engraved annular circles 7, 11 and 19cm dia. The table top is arranged for a free fall of 12.5mm by a cam action. Supplied complete with one brass conical mould, 65mm i.d. at base and 40mm i.d. at top, height of the mould 90mm

Request
Callback

LE Chatelier Flask

Used for finding specific gravity of hydraulic cement. Made from Borosilicate glass. The flask is 243mm in total height, having a bulb of 90mm dia of 250ml approximate capacity. The long neck of the flask has at top a funnel of 50mm dia in that fits a ground glass stopper. The neck has over-all 11mm i.d. upper portion is graduated from 18ml to 24ml with 1 ml graduation. Just at the bottom of the neck 1 ml capacity is marked in between there is 17 ml capacity bulb.

Request
Callback

We are enlisted as a leading manufacturer, wholesaler and supplier of Concrete Slump. The offered concrete slump is provided in numerous specifications so as to fulfill the needs of customers. Offered concrete slump is inspected by our quality controllers so as to ensure its excellence. This concrete slump can be obtained from us at affordable price from us within the promised time frame.

Features:

• Easy to operate
• Perfect finish
• Longer service life

Request
Callback

Backed by our rich industrial experience in this domain, we are devotedly engaged in offering a wide assortment of Compaction Factor Apparatus. The offered product is manufactured with the help of quality approved raw material and cutting-edge technology under the supervision of skilled professionals. Prior dispatch, the entire range is rigorously tested on various parameters of quality to ensure our zero-defect policy at clients' end. Besides this, clients can avail it from us at affordable prices.

As per IS: 1199. The instrument comprises of a slump cone with a hopper, specimen container, a transparent plastic plate attached to a graduated rod, mounted on a vibrating table, and a tamping rod 16 mm dia. x 600 mm long. The vibrating table has fixed amplitude and frequency of vibration, imparted by a motor drive mechanism.

Features:

• Light weight
• Highly durable
• Robustness

Request
Callback

RLE-503

Feature :

• Air Entrainment Meter, IS: 1199, IS: 9799,BS 1881-106,ASTMC231.
• Consists of a pressure tight flanged cylindrical measuring bowl Fitted fitted with a removable flanged conical cover assembly With a seal in between. Conical cover has an air valve and a Pet cock for bleeding off the water. A cylindrical stand pipe, Which is graduated in air content, is fixed to the conical cover assembly. The whole assembly is mounted on a flat base. Each apparatus is supplied complete with a pressure bulb or Air pump, calibrating cylinder, pressure gauge, funnel, trowel and tamping bar.
• Air Entrainment meter 0.005 cu. Mt.(5 litre) For maximum size Aggregate 38 mm. Complete with Pressure bulb/hand pump, tamping bar, Rubber mallet, Straight edge.
• Air Entrainment meter 0.001 cu. Mt (10 litre) for maximum size aggregate 75 mm. Complete with Pressure hand pump, tamping bar, Rubber mallet, Straight edge

Request
Callback

Permeability Apparatus (Single Cell Model)

RLE-511

One of the durability test of concrete is to determine permeability of water through specimen. Permeability apparatus is used for determining the permeability of cement mortar and concrete specimens of 15cm cubes cast in the laboratory.

Specification :
The concrete permeability apparatus comprises of a brass / gunmetal cell of Square/Round cross-section mounted on a stand and a pressure chamber is connected to the cell through copper tubing and T-connector mounted on the stand with sleeve packed valve and rubber hose pipe with end connections. The cell assembly consists of one base plate, one metal funnel and one top plate. The pressure chamber is fitted with a pressure regulator which helps in regulating the pressure from 0-15kg/cm sq. Gauge is for indicating the pressure in the cell. A foot pump and a pressure tube is supplied to develop pressure in the chamber. The apparatus is supplied with a measuring cylinder 500cc to measure percolated quantity to water. Pressure can also be applied; by a pressure air line or by a compressor which can be supplied at an extra cost.

Request
Callback

Permeability Apparatus (Three Cell Model)
RLE-511(A)

AS PER IS 3085

Three pressure gauges for indicating pressure in each cell are supplied apart from the main pressure gauge which indicates pressure chamber.

Request
Callback

RLE - 501

Reliable Compaction Factor Apparatus that are designed for used for influential the workability of fresh tangible, provide the utmost size of the summative does not go beyond 38 mm.

Features

• Best in quality standards

• Latest finish

• Nominal rates

• Light weighted

Specifications

• It consists of two rigid conical hoppers and a cylinder mounted on a rigid metal frame.
• The lower openings of the hoppers are fitted with hinged trap-doors having quick release catches.
• A circular metal plate is provided to cover the top of the cylinder. Supplied complete with one plasterer's trowel and one tamping rod, 16mm dia x 600mm long, one end rounded.

Request
Callback

Product Details:

Consists of a steel table top 76.2cm ( 30 inch. Dia) Finely machined. The integral cast ribs are designed for support and strength. The stand is fabricated out of cast iron and is of study construction. Holes for mounting in foundations are drilled in the base plate. The ground and hardened steel cam is designed to fit and drop the table by 12.5mm. Electrically operated to raise and drop the table top, approx. 15 times in 15 seconds, Suitable for operation on 230 Volts, 50 cycles, A.C. supply. Supplied with one conical mould with two handles, 12cm height, having 17cm. Inside Dia. at the Top and 25cm inner dia. at the base. Complete with a tamping rod 16mm dia x 600mm long one end rounded.

Request
Callback

Additional Information:

• Item Code: RLE-100
• Delivery Time: 2 DAYS

Product Details:

The instrument is used for workability as well as consistency of fresh concrete. A slump Cone and a graduated rod supplied with the instrument helps the operator to find out slump values and vibration table with container and acrylic disc is used to find out workability of concrete expressed in Vee Bee degrees, which is defined as the time in seconds to complete required vibrating at which the fresh concrete flows out sufficiently to come in contract of the entire face of acrylic disc.
Specification:
The equipment consists of : A vibrating table size 380 mm long and 260 mm wide, resting upon elastic support at a height of about 305 mm above the floor, complete with Start/Stop switch, cord and plug. A holder is fixed to the base in to which a swivel arm is telescoped with funnel and guide swivel arm is also detachable from the vibrating table. The divisions of scale on the rod record the slump of the concrete in millimeters. Supplied complete with a sheet metal container with lifting handles which can easily be fixed to the vibrating table. A slump cone open at both ends with lifting handles and a tamping rod of size 16 mm dia and 600 mm long rounded at both ends.

Request
Callback

Additional Information:

• Item Code: RLE-121

Product Details:

Request
Callback

Additional Information:

• Item Code: RLE-CC-001
• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer),D/P,D/A

Product Details:

In these load frames “C” channels are used, they are welded at the top as well as bottom and with stand high loads. A hydraulic jack is fitted at centre of the base of the load frame, over which can be fitted lower platen and spacer block with the help of centering pin. A lead screw passes through the top of the frame. To the lower end of this lead screw is fixed the upper platen with spherical seat for self alignment. The platens are accurately machined, hardened and polished. The lower platen grooves to correctly place the specimen.

Note: The platens are normally rectangular on shape, but no special request square platens or circular platens can be supplied at an extra cost.

 

Request
Callback

Additional Information:

• Item Code: RLE-149
• Delivery Time: Ready Stock

Product Details:

The  concrete block pavers according to the requirements of the related standards. as per IS 15658:2006

Capacity 50 ton
Least count 0.01 n 

Request
Callback

Vicat Apparatus (Setting Time & Consistency of Cement) as per IS: 5513. The apparatus consists of initial needle, final needle, consistency plunger, conical vicat mould, glass plate. The apparatus is provided with dashpot arrangement for jerk free lowering of needles

Available with

• Vicat mould 60mm top dia, 70mm bottom dia and 40mm height
• Vicat Mould 70mm top dia, 80mm bottom dia and 40mm heigh

Request
Callback

We are actively engaged in manufacturing, wholesaling and supplying superior quality Flow Table. The offered flow table is inspected by our quality analyst on diverse parameters so as to supply defect free range to customers. As well, our flow table is provided in several specifications as per the needs of customers. Our flow table can be purchased at nominal rates within the committed time - frame.

Features:

• Robust structure
• Efficient performance
• Durable

Available In Models:

• Hand operated with M.S. table top
• Motorised with M.S. table top
• Hand operated with Gun Metal table top
• Motorised with Gun Metal table top

Request
Callback

As per IS: 5514. Used for soundness test of cement. The apparatus consists of a small split cylinder forming a mould of 30mm internal dia. and 30mm high. On either side of the split cylinder, two parallel indicating arms with pointed ends are fixed. The mould is supplied with two glass plates and lead weight. Set of six moulds supplied in a cardboard box.

Request
Callback

LE Chatelier Water Bath

Double walled inner chamber in stainless steel outer chamber in mild steel temperature range Ambient to 100°C controlled by capillary thermostat. Accuracy ± 1°C operated on 230V A.C. Single Phase. These baths are suitable for washing Marshall specimen. Lid is made up of stainless steel with a hole for glass thermometer to penetrate. 

Following sizes are available :
a) 12" length x 9" width x 7" height having rating 750W.
b) 18" length x 12" width x 7" height having rating 1500 W.
Customised sizes also available. 

Request
Callback

Shrinkage Bar Mould (One Gang) RLE-102

The mould is used for casting specimens of cement & aggregate combinations for measuring the potential expansive alkali reactivity.

Specification : The mould, which has 25 mm x 25 mm x 250 mm, effective gauge length is made of mild steel and has accurately machined faces. The parts of the moulds are tight fitting and firmly held together when assembled. Supplied complete with base plate and four stainless steel smooth reference pins.

Request
Callback

Same as RLE-102 but with Two compartments assembled on angle base plate

Request
Callback

Prism Mould Three gang (40.1x40x160mm)

It is supplied complete with base. All parts are marked with thei dentification number for correct assembly. Each mould is individually verified in the dimensional tolerances, hardness, squareness, flatness & roughness. 

Request
Callback

Vibrating Machine

Specification : The machine consists of a vibrating frame assembly and an electric motor mounted on a sturdy base. The complete frame assembly consists of a vice to hold a 7.06cm cube mould and two studs threaded at top and a hopper to feed the sample in the mould. This assembly is supported on four springs and has an in built rotating shaft which rotates eccentrically and thus imparts vibrations to the entire frame. A balance weight is an integral bottom part of the frame. The centre of gravity of the assembly is brought to the centre of the eccentric shaft within a distance of 25mm below it. The electric motor drives the shaft of the frame and thus imparts required vibration to the moulds. The frequency of vibration is 12000 +/- 400 Vibration Per Minute. Supplied complete with on 7.06 cm Cube Mould with loose base plate, a time switch 0-5mins x 1mm.

Spares : Set of springs, belt and belt guard.

Request
Callback

As per IS: 1199. The instrument comprises of a slump cone with a hopper, specimen container, a transparent plastic plate attached to a graduated rod, , mounted on a vibrating table, and a tamping rod 16mm dia. x 600mm long. The vibrating table has fixed amplitude and frequency of vibration, imparted by a motor drive mechanism.

Request
Callback

Gang Mould (Three Gang) 

 Moulding of 40mm, 50mm, 100mm specimens. Manufactured from Mild Steel / Cast Iron / Bronze and supplied complete with base plate

Request
Callback

RLE-502


Specification :

• Vibrating Table for compaction concrete cube, cylinders.
• The Table Deck size 50cm x 50 cm and has stops along its edges to prevent Moulds from walking off the table during vibration.
• The variably pitch pulley arrangement permits the frequency to be varied sleeplessly
• between a maximum of 3600 vibrations down to 2600 vibration per minute.
• A speed regulation handle is provided for increasing or decreasing the frequency.
• The vibrator is mounted on a cushioned steel vibrating deck.
• A switch is provided for starting the motor operation on 440 V, 3 phase, A.C. supply.

Request
Callback

Our firm is engaged in precisely manufacturing and supplying high quality range of Cube Mould. These products are precisely fabricated making use of splendid quality raw material & advanced techniques in total compliance with the set international norms. Our skilled team tests each product before delivering to client to make sure their perfection. In addition to this, offered products can also be availed by customers in assorted specifications according to the varied requirements of patrons.

Available In Sizes:

• 150 x 150 x 150 mm (C.I.)
• 100 x 100 x 100 mm (C.I.)
• 50 x 50 x 50 mm (C.I.)
• 70.6 x 70.6 x 70.6 mm (M.S.)

Features:

• Reliable
• Durable
• Perfect finish

Request
Callback

Gauging Trowel

Weight approximately 210 gms.. Best quality with hard wood handle blade length 200mm.

Request
Callback

Straight Edge

 Used to remove excess material when molding cube and cylinder speciments. Conduction slump cone and air meter tests.

Flat bar made from steel.

Model Description
RLE:2015: 2” X 18” (5.1 X 45.7CM)
RLE:2016: 1” X 12" (2.5 X 30.4CM) 

Request
Callback

Tamping Bar

This is used for compacting concrete into cube moulds. This rod is made of steel it is 16mm dia., 600mm in length and rounded at both ends.

Request
Callback

Tamping Rod

This is used for compacting concrete into cube moulds. This rod is made of steel it is 16mm dia., 600mm in length and rounded at both ends.

Request
Callback