Soil Testing Equipment

Laboratory Vane Shear (Motorised)

Consists of a torque head adjustable in height by means of a lead screw rotated by a drive wheel to enable the vane to be lowered into the specimen. Rotation of the vane is by means of a hand wheel which operates a worm gear arrangement turning the upper end of a calibration torsion spring, vane dia, rod dia, vane size & vane height are as per IS specifications. The vane shaft is attached through the hollow upper shaft to a resettable pointer, which indicates the angle indicates the angle of torque on a dial graduated in degree the dial reading multiplied by spring factor gives the torque a container for soil sample is also supplied & a sampling tube of 38mm. i.d. & 150mm long can also be used as container . Supplied with set of four springs, one each of approx. 2 kgs/cm sq., 4kgs/cm sq., 6 kgs/cm sq. & 8kgs/cm sq. complete as above in a wooden carrying case. Electrically operated rate of rotating is 1/60 R.P.M. Suitable for operation on 230 V A.C. Single Phase.

Request
Callback

 Consolidation Apparatus (Single Gang) 

Consolidation test is un-dimentional test considered extremely important in soil mechanics. Sample taken from adjacent areas of a single site show differential settlement even when tested using same techniques. Soil of similar strength may show varying consolidation. Samples are very carefully prepared and vertical settlement of the specimen in saturated or drained conditions carefully recorded when known load is applied.

SPECIFICATION:
The standard outfit comprises of the following items. Loading unit, maximum capacity 20kg/cm.sq. Having a loading yoke connected to a lever arm with a counter balancing adjustment and having a lever ratio of 1:1 the whole assembly being mounted on a sturdy steel frame stand. The loading unit is so designed that it can be used for consolidation cells of different diameters as well as different dia floating ring type consolidation cells. Fixed ring type Consolidometer (Odeometer) cell assembly for testing 60mm dia x 20mm thick specimen comprising: Fixed ring for specimens 60mm dia x 20mm thick with guide ring. Top and bottom porous stones for 60mm dia specimen. Perforated pressure pad, Channeled base with water inlet and gasket Flanged water jacket, water reservoir with plastic tube and pinch cock. Set of weights to give a pressure of 10kg/cm.sq. On 60mm dia specimen, comprising : 7 nos. 0.05 kg/cm .sq., 5nos. 0.1 kg/sq.cm., 6nos. 0.5kg/sq. cm., and 5 nos. 1.0 kg/sq.cm. Supplied complete as above but without dial gauge. 

ACCESSORIES :
Dial gauge 0.002 mm x 10mm. Extension piece, 40 mm long, consolidation test forms pad of 50 for one dimensional consolidation. 

OPTIONAL EXTRAS : 
Varying head stand pipe, 50cms. Long with mm. Scale. Fixed ring type of Consolidometer (Odeometer) cell assembly for 50mm. dia x 20mm thick specimens , complete with fixed ring guide ring. Pair of porous stones, perforated pressure pad, channeled base, gasket and flanged water jacket. Set of weights to give a pressure of 10kg/sq.cm. on 50cm. dia specimen. Fixed ring type of Consolidometer (Odeometer) cell assembly for 70mm dia x 20mm thick specimens, complete with accessories as above.Set of weights to give a pressure of 10 kg/sq.cm. on 70mm dia specimens. Fixed ring type of consolidometer (odeometer) cell assembly for 100mm dia x 25mm thick specimens, complete with accessories as above. Set of weights to give a pressure of 10 kg/sq.cm. on 100mm. Dia specimens.

Request
Callback

Relative Density Test

Relative Density Test

The equipment is used for the determination of the relative density of cohesion less free draining soils and meets the essential requirements.

Specification :
The equipment consists one each of: Vibratory table, with a cushioned steel vibrating decks about 75cm x 75cm. It has a frequency of approximately 3600 vibratory table, minute under a 11.5kg load. Amplitude is variable in between 0.65mm in step of 0.05 to 0.25mm, 0.25 to 0.45 mm and 0.45 to 0.65mm. Suitable for operations on 415V, Three Phase supply. Cylindrical metal unit weight mould, 3000ml. Capacity.Guide sleeve with clamp assembly. Surcharges base plate for mould. Handle for surcharge base plate. Surcharge weight. The total weight together with surcharge base plate and handle is equipment to 140 kg. /sq. cm. For mould. Cylindrical metal unit weight mould 15000 ml. capacity. (Total weight together with the above mould & surcharge weight is equivalent to 140 kg./sq. cm) dial gauge 0.01mm x 50mm travel. Extension piece 25mm for dial gauge.

Request
Callback

Pycnometer

Useful to determine specific gravity of clays, sand and gravel of size smaller than 10mm.
SPECIFICATION :
Comprises a 1 kg. glass jar with brass cone. Locking ring and rubber seal.

SPARE : Rubber seal. 

Request
Callback

Product Details:

Rapid Moisture Meter

The unit consists of a pressure vessel with clamp for sealing cap, capacity is 6 gms . Rubber sealing gasket, pressure gauge calibrated in percentage moisture content 0-50% x 0.50% on the wet weight basis, a counter poised balance for weighing sample, a scoop for measuring carbide reagent, a bottle of reagent, one cleaning brush and a set of 4 steel balls for thorough mixing . Complete in highly polished wooden carrying case with handle.

Request
Callback

Additional Information:

• Item Code: RLE-S-001
• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer),D/P,D/A

Product Details:

As a prominent organization, we are engaged in offering a high quality Sieve Shaker Hand Operated. These sieve shakers are convenient for bench mounting & can takes upto 7 sieves operated by hand wheel. Also, we manufacture these sieve shakers using quality tested material & contemporary technology following the set norms of industry. Offered sieve shakers are checked by our quality controllers on various parameters in order to supply flawless range to customer’s end.

Features:

• Smooth functioning
• Robust construction
• High efficiency

Other Details:

Hand operated:

• This sieve shaker is convenient for bench mounting
• It can takes upto 7 sieves operated by hand wheel

Size avilable for Hand operated sieve shaker:

 

• 8” Diameter
• 12” Diameter

Request
Callback

Additional Information:

• Item Code: RLE-S-002
• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer),D/P,D/A

Core Cutter and Hammer

Specifications:

 

• Relevant Standard IS : 2720 p – xxix

• Cylindrical Steel Cutter : 100 mm Pipe ID / wall thickness 3mm / 130 mm long / beveled at one end

• M.S.Rammer : Solid mild steel bar Diameter 140 mm & 75 mm height screwed centrally 25 mm bright MS bar.

  Total height approximately 900 mm of both MS bar

• Steel Dolly : 100 mm I.D. Pipe , 25 mm height , wall thickness 7 mm beveled to fit on steel cutter

 

All these cube cutter dolly & hammer are highly appreciated for their following features:

 

• Rugged construction

• Longer life span

• Dimensional accuracy

• Corrosion resistance

• Seamless finish

Request
Callback

Product Details:

Casagrande method in mechanical form is known as liquid limit method and has been in use for soil mechanics for a number of decades. The liquid limit data of soils is useful to correlate mechanical properties of soil, such as compressibility and lower shear strength. Liquid limit is the water content at which soil passes from zero strength to an infinite strength, hence the true value of liquid limit cannot be determined. For determination purpose liquid limit is that water content at which a part of soil, cut by a groove of standard dimensions, will flow together for a distance of 1.25cm under an impact of 25 blows in a standard liquid limit apparatus. The soil at the water content has some strength which is about 0.17N/cm. sq. (17gms/sq.cm.) . At this water content soil just passes from liquid state to plastic state.
It consists on a brass cup held on an adjustable bracket.
The cup can be adjusted for a fall of 1 cm and can be raised an dropped on a rubber base of standard hardness by cam action. Complete with one Casagrande grooving tool, one ASTM grooving tool and a height gauge block. A counter to register the number of blows

Request
Callback

Additional Information:

• Item Code: RLE-175

Universal Extruder Frame Hydraulic

The extractor frame is used for taking out soil samples compacted or undisturbed, from 100mm dia and 150mm dia cylinders such as Core Cutters, Proctor moulds, C.B.R. moulds etc.

SPECIFICATION :
It consists of a 50Kn capacity hand operated, hydraulic jack mounted on a suitable frame. Two plungers, one for 4”/100mm dia and the other of 6”/150mm dia moulds are supplied Height of thrust plate is adjustable.

ACCESSORIES :
Set of plungers adaptors and thrust plates for 38mm, 50mm and 75mm dia specimen.

Request
Callback

Soil Cone Penetrometer 

For determining the liquid limit of soils. This is specially useful to obtain reliable and accurate results of those soil which have low plasticity index. The percentage moisture contents determined when cone with half angle of 15-30 minutes under a total sliding weight of 148 gm penetrates 25mm gives the liquid limit. 

Request
Callback

Leveraging on the vast experience of the industry, we are engaged in manufacturing, supplying and wholesaling Sand Replacement Cylinder. Manufactured in accordance with industry standards, these cylinders are used to determine the density of soil. Complying with IS: 2720 (Part XXVIII), these cylinders are manufactured by using quality tested material obtained from the vendors of repute. Every stage of production is supervised by our experts, who ensure to maintain higher standards of quality and eliminate flaws.

Sand replacement cylinder is used to determination of density of fine, medium, compact, grained soils.

 

 

(Relevant Standard IS : 2720 p – xxviii)

Sizes available with us:

• 10 cm Diameter

• 15 cm Diameter

• 20 cm Diameter

 

Some of the specifications of these sand replacement cylinders are mentioned as follows:

 

• Offered with soil cutting and excavating tools like scraper tool and bent spoon

• Metal containers to collect excavated soil

• Glass plate: 450 mm square and 9 mm thick

• Metal tray: 300 mm square and 40 mm deep with a 100 mm hole in the center

 

Following are some of the attributes of the sand replacement cylinders offered by us:

 

• Rigid construction

• Longer life span

• Dimensional accuracy

• Corrosion resistance

 

Available in two types Powder coated and Coloured cylinders.

Request
Callback

We are indulged in manufacturing of a wide range of Sampling Augers, which can be availed by our valued clients at highly cost effective prices. Further, this equipment are extensively used to take clean samples from a certain depth of various types of soils such as hard, rocky, medium and high cohesion in such a way so that it is not mixed with other layers of soil.

Request
Callback

 Auger Post hole


Augers are used to collect disturbed soil samples at reasonal depths for laboratory tests. Augers are available in two types and each in different sizes. Blade type (posthole type) and helical type (screw type). Each auger outfit consists one each of auger head, one meter long rod, tee piece and handle. Depth of excavating can be increased using additional extension rods. 

AUGER POSTHOLE TYPE
(a) 50mm, (b) 75mm (c) 100mm dia (d) 150mm dia

Request
Callback

California Bearing Ratio Apparatus

The equipment consists one each of the following : Load frame, hand operated , capacity 5000 kg. With high and low rates of travel of the lead screw. Mould made from gun metal/brass, 150mm internal dia x 175mm high, with perforated base plate and extension collar 50mm high. Penetration piston, face dia 50mm with adjustable bracket for penetration dial gauge. Circular metal space disc, 148mm dia x 47.7mm high. With detachable handle. Annular metal weight, 2.5 kg. 147 mm dia with 53 mm dia central hole. Slotted metal weight, 2.5kg. 147mm dia with 53 dia slot. Perforated plate made of gun-metal/brass 148mm dia with adjustable stem and lock nut and a metal tripod for dial gauge. Cutting collar, Rammer 2.6kg weight with drop of 310mm. Rammer 4.89 kg. with drop of 450mm.Supplied with proving ring and dial gauge.

Request
Callback

Constant Volume Mould

For specimen size 38mm x 76mm long comprises. Split mould 38mm dia x 126mm long. End plug 38mm dia x 25mm long pair. Split collar interchangeable. Ejecting plunger 38mm dia x 126mm long. 

ACCESSORIES :
Split mould 38mm dia x 76mm long and split mould 38mm dia x 86mm long.

Request
Callback

Plastic Limit Test

Moisture contents at which soil has smallest plasticity is called limit. For determination purpose plastic limit is defined as the water content at which a soil will just begin to crumble when rolled in to a thread of 3mm dia.

Specification :
The complete set consists of one each :
1. Glass plate 20cm x 15cm having round ends
2. Brass or stainless steel rod 3mm dia x 150mm long
3. Flexible spatula 15 cm
4. Set of 6 moisture containers
5. Porcelain basin 150mm dia
6. Plastic wash bottle 500ml

Note: 
Glass Plate size 500 x 500 x 10mm can be supplied at an extra cost.

Request
Callback

Shrinkage Limit Set 

Shrinkage limit is the maximum water content at which a reduction in water content does not cause an appreciable reduction in volume of the Soil Mass. At shrinkage limit, on further reduction in water, air enters in to the voids of soils and thus keeps the volume constant. The apparatus can be used to determine shrinkage limit and to calculate other shrinkage ratio, shrinkage index and volumetric shrinkage.

Specification :
Set consists of one each :-
1. Porcelain evaporating dish
2. Shrinkage dish
3. Glass cup
4. Perspex plate with three metal prongs
5. Flexible spatula 100mm
6. Glass cylinder
7. 25ml x 1ml, supplied without mercury

OPTIONAL ACCESSORIES:
Mercury supplied in bottle of 500 gms. at an extra cost.

Request
Callback

Linear Shrinkage Mould

 A simple mould which is filled with the soil under test. This is then dried and the resulting decrease os length of the specimen measured is expressed as the linear shrinkage. It is 25mm Dia. x 12.5mm Height x 140mm Length. 

Request
Callback

Soil Hydrometer

Used for grain size analysis of soils where more than 10% of the material will pass through 75 microns B.S. sieve. Manufactured from clear transparent glass having uniform clarity throughout the upper end on which density scale is engraved. The scale range is 0.995 to 1.030 0 density (gms./cc) at 27^oC smallest division on the scale is 0.0005

Request
Callback

Mud Balance 

Designed to find out specific gravities of semi liquids like mud and other liquids having densities in the range 0.8 to 2.5. It has a stainless steel bam calibrated specific gravities from 0.8 to 2.5. A stainless steel cup with lid and overflow vent is fitted on one side of the beam. A counter weights with cursor slides over the graduated scale. The beam has a knife-edge at centre which rests in a fulcrum fitted in the stand. Leveling screws and spirit level are fitted to the stand. 

Request
Callback

1. Consists of 100 mm dia. X 1000 cc volume Mild Steel mould with base plate & collar and 2.6 kg x 310 mm controlled fall steel rammer (Standard)            
2. Consists of 150 mm dia. X 2250 cc volume Mild Steel Mould with base plate & collar and 4.89 kg x 450 mm controlled fall steel rammer (Modified)

Request
Callback

Being a quality-centric company, we are engaged in offering a superior quality Gyratory Sieve Shaker. The offered sieve shaker is used in chemical industries, pharmaceutical industries, abrasive industries, food industries & metallurgy industries. Offered sieve shaker is inspected by our quality controllers so as to ensure its excellence. This sieve shaker can be obtained from us at affordable price from us within the promised time - frame.

Features:

• High productivity
• High storage capacity
• Robust construction

Specifications:

• Totally-enclosed design
• Anti-blocking,1-3 decks
• Smooth operation
• Work on 220/230volts single phase A.C
• Diameter: 150 mm or 200 mm

Applications:

• Abrasive Industries
• Food Industries
• Sugar Industries
• Chemical Industries
• Pharmaceutical Industries
• Mining Industries
• Metallurgy Industries
• Recycling Industries

Request
Callback